Facebook Twitter 건의문의 개회사
바로가기
m·FIELD Horizon
YouTube
DESIGNONEX
DesignOneX CMS
기술 및 사업
미디어 자료실
뉴스 & 이벤트
Contact Us
로그인 회원가입
고객센터

수소저장합금

MH-200L 캐니스터 풀셋

H Horizon
2015.11.25 21:00 5,283 0

2025 메탈하이드라이드 200L 풀패키지 (SC-390-60B)


✔ 합리적인 가격의 메탈하이드라이드 캐니스터 패키지를 공급합니다.


호라이즌의 H-Series와 완벽히 호환되는 메탈하이드라이드 수소저장합금은 200L와 500L로 나뉘며, 가볍고 합리적인 가격을 자랑합니다. 메탈하이드라이드 수소저장합금은 각종 그라운드에 사용되는 Application (휴머노이드 로봇, 자동차, 수소연료전지 바이크) 등 에 이르기까지 다양한 솔루션에 접목됩니다. 가성비가 매우 좋은 제품으로 피드백 되고 있습니다.

 



용도: 저압으로 경제적인 수소실린더를 요구하는 시스템 (호라이즌 모든 스택과 호환, 연동됩니다)

✔ 기타 사이즈는 별도 문의주시면 공급이 가능합니다.








 
제품 SPECIFICATION

 

 

모델명 (Model Name)

SC-390-60B

워터볼륨 (Water Volume)

390ml

지름 (Diameter)

60mm

캐니스터 두께 (Wall Thickness)

3.4mm

길이 (Length)

25mm

충전압력 (Charging Pressure)

Approx. 1Mpa (10bar)

용량 (Capacity)

200L H2 Gas

용기스펙 (Canister Spec)

0.39L

  

* 본 패키지에는 200리터 메탈하이드라이 실린더 전용 Push & Pull타입 레귤레이터가 포함되어 있습니다.

 


 

 


 

 

* 본 패키지에는 아래의 충전용 튜브가 포함되어 있습니다.




 

제품 설명

 

Horizon MH-200L 메탈하이드라이드 실린더는 당사의 연료전지 스택에 최적화 되어 설계된 제품입니다. 알루미늄 합금 재료 인클로저와 수소 흡수를위한 AB2 합금으로 되어 있으며, 액티베이션 (활성화) 후 (아래의 활성화 과정에 대한 지침 참조) AB2 합금은 수소를 흡수하여 포화 상태까지 열을 방출 할 수 있습니다. 캐니스터의 내압은 주위 온도 20 ℃ -25 ℃에서 8bar로 유지되며 무게는 1.8 gram 높습니다. 캐니스터 밸브가 열리고 압력이 감소되면 열을 흡수하는 합금에서 수소가 지속적으로 방출됩니다. 열 흡수율이 감소하면 수소 방출 속도도 감소합니다. 캐니스터 인클로저 재료는 가스 흡수 및 방출 공정 중에 합금의 열전도를 용이하게 할 수있는 우수한 열전도 특성을 갖는 알루미늄 합금으로 만들어집니다. 합금의 기체 흡수 효율은 습기로 인한 산화에 의해 크게 영향을받을 수 있으므로, 99.99 % 이상의 순도를 가진 건조 수소 기체가 사용에 필요합니다.




충전 과정 (How to Recharging the MH-350L Cylinder?)



Step 1


렌치를 사용하여 이중 가스 압력 조절기를 현지 가스 회사에서 얻을 수있는 가압 수소 실린더에 시계 반대 방향으로 단단히 조이십시오. (아래 그림 참조)

Use a wrench to anti-clockwise screw securely the dual headed pressure regulator to the pressurized hydrogen cylinder that can be obtained from a local Gas Company. (See pictures below)



mh-01.png



Step 2

다시 렌치를 사용하여 제공된 양방향 압력 조절기에 제공된 수소 케이블의 너트를 조입니다. 렌치를 반 시계 방향으로 돌려 너트를 조여야합니다. (아래 그림 참조)
Again using a wrench, screw the nut on the hydrogen cable provided to the dual headed pressure regulator provided. The nut needs to be tightened by turning the wrench anticlockwise. (See pictures below)


 

mh-02.png
 

 

 

Step 3


금속 수 소화물 용기를 수평으로 덮을 수있는 플라스틱 욕조를 준비하십시오. 금속 수문 용기를 덮을 수있는 충분한 온도 (주위 온도)를 유지하십시오. 안전 캡을 푸십시오. 수소 케이블의 다른 쪽 끝을 잡고, 케이블에 단단히 고정 될 때까지 캐니스터를 시계 방향으로 돌려서 금속 수 소화물 캐니스터를 케이블에 연결하십시오. (아래 그림 참조)

Prepare a plastic tub that the metal hydride canister can lie in horizontally, with enough water (ambient temperature) to cover the metal hydride canister. Unscrew the safety cap. Holding the other end of the Hydrogen cable, connect the Metal Hydride canister to the cable by turning the canister clockwise until it is securely fastened to the cable. (See pictures below)



mh-03.png
 

 

 

 

Step 4


모든 연결이 안전하다고 판단되고, 모든 밸브가 MH-350실린더 (금속수소화물캐니스터)에서 닫혔는지 점검하고 듀얼 헤드 압력 조절기도 닫힌 상태 (핸들이 시계 방향으로 완전히 밀착 될 때까지 시계 방향으로 돌리십시오)에서 듀얼 압력 레귤레이터를 조절합니다.

Check all the connections are secured and all the valves are closed on the Metal Hydride canister, and the duel headed pressure regulator is also in the closed condition (turn the handle anticlockwise until it is tight) so that the dual pressure regulator shows a zero reading on both dials.


 

mh-04.png
 

 

 

Step 5


압축 된 수소 캐니스터 밸브를 시계 방향으로 돌려서 압축 된 캐니스터 압력 판독 값을 제공하는 오른쪽의 압력 게이지를 볼 수 있도록 푸십시오.

Unscrew the compressed hydrogen canister valve clockwise so that you can see the pressure gage on the right providing you with the compressed canister pressure reading.


 

mh-05.png
 


 Step 6

메탈 하이드 라이드 캐니스터의 밸브를 시계 반대 방향으로 돌려서 열어 물 아래에 수평이되게 물통이있는 욕조에 넣습니다.
Turn the valve on the Metal Hydride Canister anti-clockwise to open it and place it into the tub full of water so that it lies horizontally under the water.

 



mh-06.png
 


Step 7

천천히 양방향 압력 조절 밸브를 시계 방향으로 돌려서 왼손잡이 압력 판독 값을 확인하십시오. 20Bar (290psi)에 도달하면 약 60 분 동안 메탈 하이드 라이드 용기를 채 웁니다. 그리고 다이얼이 0으로 천천히 움직이는 지 확인하기 위해 양방향 압력 조절 밸브를 반 시계 방향으로 돌려 단단히 조입니다. 다이얼이 움직이지 않으면 용기가 완전히 채워 졌음을 의미합니다.
Slowly turn the dual headed pressure regulator valve clockwise, making sure you watch the left-handed pressure reading. When it reaches 20Bar (290psi) allow the Metal Hydride canister to fill for about 60 minutes. And then turn the dual headed pressure regulator valve anti-clockwise until it is tight to check if the dial moves slowly towards zero. If the dial does not move that means the canister is fully filled.

mh-07.png
 

 

 

Step 8


압축 된 수소 캐니스터와 금속 수 소화물 캐니스터가 단단해질 때까지 나사를 조이고 압력 조절기가 닫힐 때까지 시계 반대 방향으로 돌리십시오. 이 때 낮은 압력계는 여전히 용기에 충전 한 압력을 나타냅니다. 천천히 렌치를 사용하여 케이블과 압력 조절기 사이의 연결을 느슨하게하여 캐니스터의 수소를 방출하십시오. 미터가 0으로 돌아갑니다.

Screw the compressed hydrogen canister and the metal hydride canister until they are tight and also turn off the pressure regulator anti-clockwise until it is closed. At this time the lower pressure meter still indicates the pressure you charged the canister. Slowly use the wrench to loosen the connection between the cable and pressure regulator to release the hydrogen in the

canister. The meter will be back to 0. 



process7.png



 

 

Step 9


금속 수 소화물 용기를 끄고 나면 수소 케이블을 분리하고 용기에 압력 조절기를 조이십시오. 그런 다음 튜브를 압력 조절기에 연결하고 금속 수소 캐니스터 나사를 켜서 수소를 공급하십시오.

After turn off the metal hydride canister you can disconnect the hydrogen cable and screw the pressure regulator on the Canister. Then connect the tube to the pressure regulator and turn on the metal hydride canister screw to supply hydrogen.


mh-09.png
 

* Refilling Adaptor와 40bar Pressure TUBE와 함께 구매해보세요!




✔ 혹시 자동충전 시스템이 필요하신가요? 그렇다면~!

  


아래 시스템을 구매하시면 MH-200L Canister와 레귤레이터와 함께 공급됩니다.


e0c05ffdc6f3901b66549750ecec1fb0_1734089



l 해당 스펙은 철도, 선박, 발전분야로 대형화를 위해 개발된 스택임, 선박 및 차량 적용 시 변경가능함

l​ 호라이즌 1, 2, 3세대 시스템은 DCDC, 모니터링프로그램을 기본제공합니다.

l 해당사이트 내 모든 컨텐츠소유권은 (주)호라이즌퓨얼셀코리아에 있습니다.

l 장수호라이즌뉴에너지테크놀러지스 의 전 제품은 호라이즌퓨얼셀코리아를 통해서만 공급됩니다. 

허가받지 않은 컨텐츠의 무단 사용, 배포 및 상업적 도용은 법적 처벌 대상이 됩니다.

목록